GETTING STARTED

This getting started document guide you to setup your NCheck visitor management system and perform the initial configuration of the visitor management system. You can follow below steps to setup and configure the system and start appointment booking, visitor tracking and managing.

Figure 1 Visitor Management overview

Planning the system

NCheck visitor management has following components.

1. Server

   Server is required component. Depending on the visitor management requirements following deployment options available for the server.

   1. Cloud subscription

      NCheck visitor management cloud subscription can be purchased. No IT expertise need to configure the server

   2. Onpremises

      NCheck visitor management onpremises server version can be download and installed. This requires additional overhead on system maintainance.

2. Online registration

   Online registration is used for appointment booking. It can be enabled from the visit configuration.

3. Self-registration Kiosk

   Self-registration Kiosk is used to register for an appointment on arrival to the organization.

4. Visitor attendance and access control device

   Visitor attendance and access control devices are used to authenticate visitors and control visitor access only for the places relevant to the appointment.

5. Assistant device

   Assistant device can be used register for an appointment, authenticate and manage visitor by an assistant assigned from the organization.

6. Information Display

   Information display is used to provide information about current appointments in progress

Depend on your visitor management system requirements, you will select required components. Minimal visitor management system can have only the NCheck visitor management Server.

Server Installation

Depending on the customer requirements following options available for server

1. Start NCheck visitor management with cloud

2. Start NCheck visitor management with on-premises server

Start NCheck visitor management with cloud

To start with NCheck visitor management cloud server, you have to signup first. Launch signup page from signup url.

Figure 2 NCheck visitor management signup page

File the NCheck visitor management signup form and select signup button. After successful signup, you will receive verification email for the email address you have provided when signup. If the verification email did not receive, select “I didn’t receieved a veriication email” option as shown in Figure 3 . It will resend the verification email as shown in Figure 4 .

Figure 3 Verify email address

Figure 4 Resent email verification dialog

Open the verification email you have received.

Figure 5 Verification email

Select verification link to verify email. Once the email account has verified, it will open a confirmation page as shown below.

Figure 6 Email verification confirmation page

Select login-in button to login NCheck visitor management cloud account. You can use username and password received in verification email login to cloud account. Refer Log in to NCheck visitor management Control Panel section for more details about cloud account login.

Note

Free plan will be assigned to your NCheck visitor management Cloud subscription after successful signup. You can change the plan of your subscription from administration control panel. Refer plan and pricing for more details about available subscriptions.

Start NCheck visitor management with on-premises server

NCheck visitor management server installed in your location. Server can be installed on machine with following configuration.

1. 64bit Windows with Java runtime 1.8 or above

2. Processor with two cores of 2.4 GHz

3. 4GB free memory

4. Network interface

Download NCheck visitor management server installation package from download page. Run installer package to install the server. The installation process will guide you through the installation process. At the end of the installation,

1. Installation waits for starting NCheck visitor management server.

2. installation completion dialog shows the instructions to log in to the NCheck Control Panel.

   

   Figure 7 Server installation completion dialog

Note

NCheck visitor management server may fail to start if it cannot use the default port 8443. You should change the server configuration and save to start the server

Log in to NCheck visitor management Control Panel

NCheck visitor management server can be access from web browser as mentioned below

Table 1 Access NCheck visitor management web control panel

Version	URL	Remarks
Cloud	https://vmcloud.ncheck.net
On Premises	https://server:port	Server – Sever name or IP address Port – NCheck visitor management service port configured on the server. Default port is 8443. Default user name “admin”, password “admin”
	NCheck Control panel can be access from the server tray icon menu from the server	Default username “admin”, password “admin”

Note

For on-premises server by default, server uses a generated self-signed certificate. When you first time connect to the server through browser, Browser may warn you about Server SSL certificate. You should accept to continue.

After first time login, a system configuration guidance message to set up your first visit schedule in the system.

Figure 8 System configuration guidance message

Road map to configure system

To configure the NCheck visitor management the following steps need to be followed in order

1. Create a location (Optional)

2. Create a visit schedule

3. Setup visitor self-registration kiosk and place a visitor appointment

4. Set up visitor attendance device

5. Enroll visitor biometric

6. Enable Biometric authentication (Optional)

7. Configure Visitor access control (Optional)

8. Configure door control (Optional)

9. Set up visitor information display

10. Visitor Assistant device

Create a location (Optional)

New visit location can be created from “Visit schedules and locations.”

Figure 9 Location management view

Select Add button. Add new location dialog will be shown as below.

Figure 10 Add new location dialog

Create a visit schedule

A new visit schedule can be created from “Visit schedules”. Schedule can be created to allow visitors in a specified time of selected days in week. We will create a visit schedule to allow visitors to meet an employee at any time (everyday, 24 hours) below.

Figure 11 Schedule management view

Select the Add schedule button. It will show Add schedule dialog with list of scenarios to select one.

Figure 12 Add schedule dialog

Select the best scenario from the list of scenarios and select Next button. It will Add schedule detail dialog to add schedule details.

Figure 13 Add schedule detail dialog.

Enter the schedule name. Select Save button to create a new visit schedule.

Setup visitor self-registration kiosk and place a visitor appointment

Figure 14 Registration device for selected schedule

Select Registration device button for the schedule. You can find the registration device registration token in Generate a new device token dialog.

Figure 15 Generate a new device token dialog for registration device

After that, Install NCheck visitor management Client for Windows or Android. Register the client using the generated device registration code. After registration, the device shows the appointment booking view for the Kiosk.

Set up visitor attendance device

Visitor attendance device is used to authenticate visitors and record visitor check in, check out and access events. Attendance device registered for the location of a visit schedule records visitor check in and check out events. Follow the steps below to set up a visitor attendance device.

Figure 16 Attendance device button for the schedule

Select the visit schedule, select Attendance device button from the schedule quick view. You can find the registration device token in Generate a new device token dialog.

Figure 17 Generate a new device token dialog for attendance device

After that Install NCheck visitor management Client for Windows or Android. Register the client using the generated device registration code. The device is registered for the location of the visit schedule. Visitors who have visit appointments at the location can check in or check out from the device.

Enroll visitor biometric

Visitor biometric collection can be configured to collect from

1. Enable Collect biometric from registration kiosk

2. Change biometric collection from attendance device

Enable Collect biometric from registration kiosk

You can follow the steps below to enable biometric collection when registration from registration kiosk device. Go to visit schedules. In visit schedule select Edit button

Figure 18 Biometric collection setting in edit schedule dialog

Select additional settings from the stepper and make sure that a biometric modality is selected for “Biometric collection” Select Save button to save if any change is there.

Change biometric collection from attendance device

Figure 19 Device management view

Go to device management and select the device.

Figure 20 Settings button for the selected device

Select the Settings button from the device quick view.

Figure 21 Self enroll template setting in device settings dialog

In the device setting dialog select Client tab and make sure that the self-enroll biometric setting is enabled

Enable Biometric authentication (Optional)

Follow steps below to configure biometric authentication for a device. Go to device management.

Figure 22 Edit device button for selected device

Select the device. From the device quick view, select Edit button.

Figure 23 Set biometric authentication in edit device dialog

In the Edit device dialog, set a biometric authentication mode for attendance device and select Save button to save changes.

Configure Visitor access control (Optional)

Visitors are allowed from attendance device.

1. A visitor has an appointment for a visit in the device location.

2. Device location is an access location for an appointment location of a visitor.

Location configuration can assign access locations for a location add/edit location. Attendance devices in access locations record access events.

Configure door control (Optional)

NCheck visitor management attendance devices can activate access door locks over the network or by executing door control programs in windows or android platforms. To configure door control, go to device management and select the attendance device. Select the Edit button.

Figure 24 Add new button in Edit device dialog

In the Edit device dialog, select Add new button next to External executables.

Figure 25 Add external executable

Fill the configuration and select Save button to save changes.

Set up visitor information display

Visitor information display devices can be used to provide information to visitors. To configure the visitor information display, follow below steps.

Figure 26 Information device button for selected schedule

Go to Visit Schedules and select the visit schedule. Select Information device button from schedule quick view.

Figure 27 Generate a new device registration token dialog

You can find the visitor information device registration token in Generate a new device registration token dialog. After that Install NCheck visitor management Client for Windows or Android. Register the client using the generated device registration code. After registration, the device shows the default visitor information view. To change the visitor information view, follow the steps below. Go to device management. For the selected the device select “Settings” button

Figure 28 Client mode setting in Device setting dialog

Select the page from the available page list You can select an internal view or provide external information URL.

Visitor Assistant device

Visitor assistance device is a visitor attendance device. But to help visitors, an assistant should be logged in to the device. Assistant is an employee in the system and should be a visitor administrator or an employee assigned for a visit schedule. Follow the steps below to register and use an assistance device.

1. Create a Visitor admin or assign an employee to the visit schedule.

2. Set up a visitor attendance device.

3. Open NCheck visitor management client. It will start visitor identification.

4. Log in assistant to the device

5. Identify a visitor. After identifying the visitor, it will show the following assistance options.

   1. Appointment – Allow assistance to view, update the appointment.

   2. Record check in, check out or access event.

6. Assistants can also create new appointments without identifying a visitor.